PEH 950 - Electric planer PARKSIDE - Free user manual and instructions

USER MANUAL PEH 950 PARKSIDE

FOR PLANING, CHAMFERING AND REBATING WOOD.

Dear Customer, We are delighted that you have decided to purchase our high quality PEH 950 power planer. Please make sure you familiarise yourself fully with the way the equipment works before you use it for the first time and that you understand how to handle electrical power tools correctly. Please read the operating instructions below and the accompanying safety advice carefully. Use the equipment only as described and for the indicated purposes. By doing this you will be able to work in complete safety and produce better results. We hope you enjoy using your planer.

PROPER USE

The electric planer is suitable for planing wood in the form of beams or boards if the workpiece is held securely in a fixed position. Any other use or modification to the belt sander shall be considered as improper use and could give rise to considerable dangers. The manufacturer will not accept liability for loss or damage arising from improper use.

FEATURES OF THE PEH 950

1 Guide handle/
planing depth adjuster
ON/OFF switch
Drive interrupt
4 Toothed belt cover
5 Rebating depth stop
6 Side fence

7 Cutting block / planer blades
8 Planing depth scale
9 Base plate
10 Vee groove
Dust outlet
Safety cover

TECHNICAL INFORMATION

Nominal power: 950 W

Nominal voltage: 230V 50Hz

Design no-load speed: n_0 12,000 rpm

Planing depth: 0 - 03.5 mm

Rebating depth: 0 - 24.0 mm

Planing width: 82 mm

Weight: 4,3 kg

Sound pressure level: 95 dB (A)

Sound power level: 108 dB (A)

Vibration: 1,9m / s^2 (hand-arm vibration)

Protection class: II / 回

IMPORTANT SAFETY ADVICE

To be read in conjunction with the advice in the accompanying booklet on safety before using for the first time.
The PEH 950 power planer is intended to be used for planing wood (e.g. beams, boards).
If the mains cable is damaged or cut through during the work - never touch the cable - pull out the mains plug immediately. Never use electrical equipment with damaged cables.
For operating the planer for longer periods and particularly if dust that may be hazardous to heath is created, the planer should be connected to a suitable external vacuum device.

Wear a dust mask.

Make sure you only use sharp blades.
Always keep the power cable fed to the rear of the machine.
Never plane over metal objects, nails or screws.
Only place the planer against the workpiece after switching it on.
The base plate 9 must always lay flat on the workpiece when working.
Do not clear dust etc. from the dust outlet with your fingers. Use a piece of wood to dislodge any trapped planing debris.

OPERATION

The PEH 950 power planer has INTELLIGENT POWER CONTROL.

This electronic management system monitors and controls your power plan in its various operating states;

Operating state

Feature

Switching On/Off:

The IPC electronic system start-up mode ensures that the motor starts up slowly and gently. This large ly avoids heavy transient current surges, and means that electrical safety cut-out devices are not generally tripped (building sites, domestic premises).

No-load running:

After switching on, the IPC electronic management system run-up mode takes the planer speed up to the pre-set required value. After this is reached, the IPC system speed control mode keeps the grinder operating at a constant speed.

WARNING:

Always remove the plug from the mains socket before working on the planer.

Take note of the mains voltage. The voltage must agree with that shown on the rating plate (equipment shown as 230V can also be used with 220V ).

ON/OFF SWITCH

On the grounds of safety the ON / OFF switch ③ cannot be locked in the ON position for continuous operation. It must always be pressed during operation.

SETTING THE PLANING DEPTH

The planing depth can be set between 0 - 3.5 mm. Turn the guide handle/ planing depth adjuster ① and set the pointer to the desired mark or value.

DUST REMOVAL AND VACUUM EXTRACTION

The planing debris removal channel ⑧ can be configured to the left or right as required by simply inserting a closing cap and vacuum hose adapter.

OPERATING INSTRUCTIONS

Always switch on the planer before making contact with the material and then guide the planer on to the workpiece.

PLANING SURFACES

Place the planer with the front of the base plate on the workpiece.

Always make sure when you are planing surfaces such as beams and boards that the base plate is in full contact with the surface to avoid the danger of blade kickback.

Always use both hands to guide the plane over the workpiece with even forward pressure.

CHAMFERING CORNERS

The vee groove 1 in the centre of the front of the base plate 2 allows you to chamfer the corners of your workpiece very quickly and easily. Place the planer on to the workpiece with the vee groove 3 on the corner and then guide the planer along the corner. Make sure you keep the angle at 45^ and an even forward pressure.

REBATING

Example set up: for right hand rebates the side fence ⑥ goes on the left and the rebating depth stop ⑦ goes on the right into the holes on the planer (with the planer viewed from above).

Set the rebating depth up to a max. 24mm using the rebating depth stop 7. Set the side fence 6 to give the required width. Adjust the planing depth scale 2 to the maximum of 3.5mm . Go over the workpiece as many times as is required to obtain the desired rebate.

CHANGING OR REVERSING THE PLANER BLADES

WARNING: Before doing any work on the planer always pull out the plug from the mains.

IMPORTANT ADVICE:

Do not unscrew the two hexagonal socket headed screws. They adjust the height of the cutting block. Adjustment is only required if you wish to change to another planer blade type e.g. a profiled blade.

HSS reversible blades are fitted as standard at the works. When you change blades, always change both blades to avoid any imbalance. When they become blunt, the PARKSIDE reversible blades can be changed without any height adjustment of the cutting block being necessary

1) First unscrew one cutting block ② only so that you can use the works-mounted second cutting block as an aid to setting up later.
2) Unscrew the three screws in the cutting block using the supplied open spanner.
3) Take the cutting block out of the planing roller.
4) Slide the planer blade sideways out of the cutting block. NOTE: The cutting block can also be dismantled, e.g. for cleaning.
5) Re-assembly with a reversed or new blade is done in reverse order.
6) Check again for safety: - the position of the planer blade in the cutting block - the balanced and secure seating of the cutting block and the 3 fixing screws - that the height adjustment is correct (2 hexagonal socket headed screws).
7) Planer blades can be obtained from the service address indicated (see guarantee).

CHANGE TOOTHED BELT

Unscrew the screws in the cover and take off the toothed belt cover ⑤ . Cut through the toothed belt with side-cutting pliers or a knife and remove the severed toothed belt. Always clean off any dirt or debris from the pulley and the drive wheel before installing the new belt.

Place the new toothed belt on to the drive wheel and push the belt over the large pulley wheel whilst turning it.

Put the toothed belt cover ⑤ back in place and fasten with the screws.

MAINTENANCE AND CARE

Clean the planer regularly. For the best results do this straight after the work has been completed. Do not allow liquids to get inside the planer. Use a soft cloth for cleaning the housing. Do not use petrol, solvents or cleaners that might attack the plastic. Air vents must always be clear and clean.

TIPS AND TRICKS

1. Do not use too much forward pressure. - Too much pressure can considerably reduce performance and increase the wear on the blades.
2. Always use sharp blades and replace blunt blades promptly. - You will get better cutting performance and extended tool life.
3. To obtain smooth planed surfaces we recommend that you use shallow planing depths and plane the surface a number of times.

Further practical tips for power tools can be found in the accompanying booklet on safety advice. We reserve the right to make technical modifications in the course of further development.

DISPOSAL

The packaging is wholly composed of environmentally-friendly materials that can be disposed of at a local recycling centre.

Please contact your local council office to find out about disposal facilities for your worn-out electrical tools.

STATEMENT OF CONFORMITY

We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare that this product conforms with the following EC regulations:

Machinery Directive:

(98/37 EC)

EU Low Voltage Directive:

(73/23 EEC), (93/68 EEC)

Electromagnetic compatibility:

(89/336 EEC)

Applicable harmonised standards:

EN 50144-1: 1998+A1:2002

EN 50144-2.14: 2001

Description / Model type:

PARKSIDE PEH 950 power planer

Bochum, 31.10.2003

Hans Kompernaß

- Managing Director

PARKSIDE

RABOT ÉLECTRIQUE PEH 950 POUR RABOTER, CHANFREINER ET FEUILLURER LE BOIS.

REEMPLACEMENT OU INVERSION DES LAMES

(73/23 EEC), (93/68 EEC)

(89/336 EEC)

EN 50144-1: 1998+A1:2002

EN 50144-2.14: 2001

Marca:

Tipo dequina:

(73/23 EEC), (93/68 EEC)

(73/23 EEC), (93/68 EEC)

Aänenpoinetas: 95 dB (A)

Aänen tehtaso: 108 dB (A)

(73/23 EEC), (93/68 EEC)

KONFORMITETSDEKLARATION

Vi, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, DE- 44867 Bochum, Tyskland forklarar harmed attenna Produkt überensättem med foljande EU-riktliner:

Maskinrriklinje:

(73/23 EEC), (93/68 EEC)

Anvanda harmoniserade normer:

(89/336 EEC)

EN 50144-1: 1998+A1:2002

EN 50144-2.14: 2001

Maskintyp/Typ:

ELHYVEL PEH 950

Bochum, 2003-10-31

Hans Kompernaβ

• Verkstallande Direktor

GARANTIE

This piece of equipment is covered by a 3-year warranty as of the date of purchase.

The equipment was produced with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its original packaging with the proof of purchase to the closest service address.

Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty.

Beaver Electronic Services · The Lodge, Premier Business Park Long Street, Walsall · West Midlands, WS2 9DY

Tel.: [phone]·Fax: [phone]

e-mail: [e-mail]

This piece of equipment is covered by a 3-year warranty as of the date of purchase.

The equipment was produced with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its original packaging with the proof of purchase to the closest service address.

Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty.

Irish Connection Ltd · 8 St Mary's Place

Howth, Co. Dublin

Tel [phone] Fax: [phone]

e-mail: [e-mail]

F GARANTIE